Wheel axle set with closed groove ball bearings for front wire spoke wheels on your Puch moped / moped.
The set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The innovation set works with spoke hubs (spoke rims).
The cable ties show you where to mount what:
- Red cable tie: wheel hub
- green cable tie: brake anchor plate
- Yellow cable ties: Replacement disk for the speedometer drive (the disk is removed if a drive is fitted)
- Blue cable ties: fork braces
Note: When mounting the ball bearings, it is important to ensure that the long spacer between the two ball bearings is mounted without play to ensure that the two bearings press with the inner ring on the bushing. If this is not observed, the ball bearings will inevitably jam.
Details
| Ø inside | 12 mm |
| Height | 9.9 mm, 5.9 mm |
| Manufacturer | swiing® ingenious parts |
| Ø outside | 29.02 mm |
| Total length | 165 mm |
| Material | Steel |
| Surface | galvanized (blue) |
| Width | 35.7 mm, 6.6 mm, 11 mm, 2.7 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Ø shaft | 11.95 mm |
| Thread length | 40.5 mm, 50 mm |
| Shank length | 74.5 mm |
| Width across flats SW | 19 mm |
| Ball bearing closed | Yes |
Suitable for the following models
| Puch |
Accessories & related products
Nut M12x1 x 10 SW19 Wheel nut galvanized
Height: 10 mm · Material: Steel · Surface: galvanized (blue) · Thread type: MF26x1 (fine pitch thread) · Drive: External hexagon · Nut type: Hexagon nut · Thread depth: 10 mm · Width across flats SW: 19 mm · Strength class: 8 · Area of application: Standard
EUR 2.25
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Diameter: 29 mm · Ø shaft: 19 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Width across flats SW: 19 mm · Ball bearing closed: Yes
EUR 43.80
Not in stock
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Ø outside: 29.02 mm · Width: 9 mm · Inner ring width: 9 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: "-" Sheet steel cage ball-guided · Material: Plastic · Material: Steel · Surface: blank
EUR 10.00
Not in stock
swiing® revival wheel nut M12x1 x 4 SW17 galvanized
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut · Thread type: MF12x1 (fine pitch thread) · Drive: External hexagon · Width across flats SW: 17 mm · Height: 4 mm · Strength class: 8
EUR 3.25
66HEROES pointed nut "Spike" M12 Inox
Manufacturer: 66HEROES · Material: Chrome steel (known as Nirosta®) · Thread type: M10x1.5 (standard thread) · Thread type: M12x1.75 (standard thread) · Thread type: M5x0.8 (standard thread) · Thread type: M6x1 (standard thread) · Thread type: M8x1.25 (standard thread) · Drive: External hexagon · Nut type: Pointed nut
EUR 7.75
swiing® ingenious wheel axle with bearing conversion kit cast hub front Ø 29 mm | Puch
Height: 5.9 mm · Height: 9.9 mm · Ø inside: 12 mm · Manufacturer: swiing® ingenious parts · Ø outside: 29.02 mm · Total length: 165 mm · Material: Steel · Surface: galvanized (blue) · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 34.5 mm · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 11.95 mm · Thread length: 40.5 mm · Thread length: 50 mm · Shank length: 74.5 mm · Width across flats SW: 19 mm · Ball bearing closed: Yes
EUR 43.80
Moped fans like you also bought:
Fuel tap horizontal M12x1 (with union nut) outgoing at the bottom
Possible lever positions: open / closed / reserve · Thread type: MF12x1 (fine pitch thread) · Material lever: Metal · Filter type: Plastic net · Ø fuel hose connection: 6 mm · Installation direction: horizontal / horizontal · Outlet direction: below · Spare tube shape: curved · Mounting type: Union nut · Reserve level: 70 mm
EUR 11.20
Fortune / Merrick 2.00-2.50 x 16/17" inner tube
Manufacturer: Fortune · Tire width [inch]: 2 - 2.5 " · Tire width [mm]: 50.8 - 63.5 · Width [inch]: 2 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Wheel size [inch]: 16 - 17 " · Wheel size [inch]: 17 " · Tire height [%]: 100 · Old designation: 20 x 2 · Old designation: 20 x 2.25 · Old designation: 20 x 2.5 · Old designation: 21 x 2 · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Valve type: TR4 Auto valve
EUR 11.20
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Nipple length: 14 mm · Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Surface: raw · Quantity: 36 pcs · Length from hook: 188 mm · Nominal diameter (thread): 3.15 mm · Ø spoke head: 5.35 mm · Color: silver · Ø spoke: 2.9 mm · Thread length: 11 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 °
EUR 61.80
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Diameter: 29 mm · Ø shaft: 19 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Width across flats SW: 19 mm · Ball bearing closed: Yes
EUR 43.80
Not in stock
Inner cable set automatic | Puch E50
Manufacturer: Made in Germany · Total length: 1600 mm · Total length: 2200 mm · Material: Steel · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Quantity: 4 pcs · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears
EUR 11.20
Collection only possible with online purchase and appointment.
