Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
| Material | Aluminum |
| Surface | blank |
| Ø axle | 12 mm |
| Ø inside | 30 mm |
| Ø Receptacle | 93 mm |
| Ø drum | 80 mm |
| Area of application | Standard, Custom |
| Number of spoke holes | 36 pcs |
| Puch |
Accessories & related products
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Ø nipple: 3.5 mm · Ø nipple: 6 mm · Nipple length: 10 mm · Number of components: 1 pcs · Ø Stranded wire: 1.8 mm · Cable length: 2200 mm · Nipple shape: Pears · Area of application: Standard
EUR 2.75
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Ø inside: 12 mm · Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Width: 8 mm · Width: 9 mm · Ø outside: 28 mm · Ø outside: 29 mm · Total length: 190 mm
EUR 35.30
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø outside: 91 mm · Ø screw holder: 6.5 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm · Ø bore: 12.2 mm · Total length: 187 mm
EUR 79.90
swiing® revival rear brake anchor plate | Puch Maxi N
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Total length: 135 mm · Ø axle: 12 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Wide cam holder: 12 mm · Cranking (offset): 10 mm · Brake lever length (lever length): 68 mm · Ø outside: 92 mm
EUR 85.60
Magura set screw M6x34 mm lock nut SW10
Surface: nickel-plated · Slotted: No · Manufacturer: Magura · Ø cable holder: 3.05 mm · Width across flats nut: 10 mm · Material: Brass · Ø Receptacle: 7.05 mm · Thread type: M6x1 (standard thread) · Total length: 34 mm · Width across flats Screw: 8 mm · Thread length: 23 mm
EUR 2.85
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Shank length: 99 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 28 mm · Thread length: 52 mm · Total length: 185 mm · Width across flats SW: 7 mm
EUR 11.30
SKF 16101 2RS1 ball bearing 12/30/8
Bearing type: Deep groove ball bearing · Stock number: 16101 · Ø inside: 12 mm · Ø outside: 30 mm · Width: 8 mm · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: "-" Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard
EUR 18.60
Moped fans also bought
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Manufacturer: GPO · Material: Aluminum · Surface: sandblasted · Ø cylinder: 38 mm · Width: 125 mm · Total length: 135 mm · Area of application: Standard · Number of fixing points: 4 pcs · Candle thread: short · Height: 55 mm · Hole pattern [mm]: 44 x 44 · Decompressor: No
EUR 37.60
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Surface: raw · Quantity: 36 pcs · Length from hook: 188 mm · Color: silver · Ø spoke head: 5.35 mm · Ø spoke: 2.9 mm · Nominal diameter (thread): 3.15 mm · Nipple length: 14 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Thread length: 11 mm · Hook angle: 95 °
EUR 62.70
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Thread type: MF12x1 (fine pitch thread) · Total length: 165 mm · Ø inside: 12 mm · Ø outside: 29.02 mm · Thread length: 40.5 mm · Thread length: 50 mm · Height: 5.9 mm · Height: 9.9 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Ball bearing closed: Yes · Width across flats SW: 19 mm
EUR 44.50
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø outside: 91 mm · Ø screw holder: 6.5 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm · Ø bore: 12.2 mm · Total length: 187 mm
EUR 79.90
Collection only possible with online purchase and appointment.
