Chrome-plated racing exhaust with attached silencer suitable for various Puch mopeds / mopeds with a straight outlet.
This tuning exhaust delivers plenty of power and is also visually stunning.
The rearmost end of the resonance body is fitted with a screw. Two additional screws with different holes are included in the scope of delivery.
These can be replaced. This changes the exhaust back pressure and therefore the performance of the silencer.
This means you have an exhaust for the lower, middle and upper speed range all in one.
You can find more racing silencers in the accessories section.
Branded product from the Portuguese manufacturer TECNO.
| Manufacturer | TECNO |
| Material | Steel, Aluminum |
| Surface | chrome-plated |
| Color | Chrome |
| Total length | 900 mm |
| Ø Silencer | 60 mm |
| Ø Internal connection | 24 mm |
| Number of fixing points | 3 pcs |
| Ø Flame tube outside | 28 mm |
| Exhaust type | Cone / double cone |
| Puch |
Accessories & related products
swiing® ingenious gasket outlet 28 mm graphite
Manufacturer: swiing® ingenious parts · Material: Graphite / Graphite · Reinforced: No · Ø inside: 27.4 mm · Thickness: 3 mm · Ø outlet inside: 28 mm · Ø screw holder: 6.6 mm · Place of use: Exhaust · Hole spacing outlet: 42.5 mm · Area of application: Tuning
EUR 8.45
Hot 
HOMOET exhaust P6 blank | Puch
Manufacturer: HOMOET · Material: Steel · Surface: raw · Surface: varnished · Color: gray · Ø outside: 88 mm · Total length: 900 mm · Ø Silencer: 50 mm · Ø Flame tube outside: 28 mm · Exhaust type: Cone / double cone · Mounting type: Tab · Number of fixing points: 2 pcs · Flame tube attachment: Stud bolts & nuts
EUR 325.50
Not in stock
Moped fans also bought
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Ignition system: BOSCH · Color: Chrome · Ignition system: DUCATI · Color: black-matt · Ø outside: 130 mm · Total length: 160 mm · Hole spacing: 137.5 mm · Number of fixing points: 2 pcs · Width: 150 mm · Height: 88 mm
EUR 171.30
Not in stock
Not so nice 
Road Master 2.25 x 17" F-323 4.P.R. Allround
Manufacturer: Road Master · Tire width [inch]: 2.25 " · Color: black · Width [inch]: 2 1/4 · Old designation: 21 x 2.25 · Speed index: B = 50 km/h · Load capacity index: 39 = 136 kg · Profile type: F-323 4.P.R. · Tire type: Allround · White wall: No · Wheel size [inch]: 17 " · Tubeless (yes/no): Tubetype TT (requires hose)
EUR 34.20
swiing® revival brake support bolt short Inox | Puch Maxi, Supermaxi
Drive: Outer edge · Width across flats SW: 13 mm · Width across flats SW: 17 mm · Thread type: MF10x1 (fine pitch thread) · Manufacturer: swiing® revival parts · Thread length: 13 mm · Ø shaft: 9.8 mm · Material: Chrome steel (known as Nirosta®) · Number of components: 3 pcs · Total length: 32 mm · Ø External head: 14 mm · Shank: Yes · Shank length: 9.5 mm · Area of application: Standard
EUR 14.70
Hot
Jammer racing clutch special 65 ccm and more | Puch E50
Thickness: 19 mm · Manufacturer: Jammer · Material: Steel · Material addition: Steel · Ø outside: 92.5 mm · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning
EUR 217.00
Not in stock
Hot
swiing® ingenious 15 mm carburetor "Tuning" camouflaged | Puch
Nominal diameter: 15 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Component group Carburetor: Carburetor complete · Carburetor type: SRE · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle size: 62 · Ø Inside entrance: 15 mm · Ø Internal connection: 20 mm · Total length: 66 mm · Mounting type: Plug connection clamped · Ø Output inside: 15 mm · Width: 50 mm · Ø Air filter connection: 20 mm · Height: 95 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle block: 2.17 · Camouflaged: Yes · Area of application: Tuning · Clamping screw torque (max.): 4 N/m · Puch OEM number: 349.1.15.100.0 · Puch OEM number: 349.2.15.800.0 · Puch OEM number: 349.4.15.500.0 · Puch OEM number: 349.4.15.000.0 · Puch OEM number: 349.4.15.300.0 · Puch OEM number: 349.6.15.400.0 · Puch OEM number: 349.7.15.700.0 · Puch OEM number: 349.8.15.400.0 · Puch OEM number: 349.9.15.300.0
EUR 91.30
swiing® revival 12 mm carburetor "Original" | Puch
Nominal diameter: 12 mm · Manufacturer: swiing® revival parts · Material: Aluminum · Component group Carburetor: Carburetor complete · Color: gray · Carburetor type: SRE · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle size: 52 · Ø Inside entrance: 12 mm · Ø Internal connection: 20 mm · Total length: 65 mm · Mounting type: Plug connection clamped · Ø Output inside: 12 mm · Width: 50 mm · Ø Air filter connection: 20 mm · Height: 108 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle block: 2.15 · Camouflaged: No · Area of application: Standard · Clamping screw torque (max.): 4 N/m · Puch OEM number: 349.6.15.400.0 · Puch OEM number: 349.7.15.700.0
EUR 79.90
Collection only possible with online purchase and appointment.
