Pinasco «EVOTEN BIG BORE» cylinder with 46 mm bore and 71 cc for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The completely reworked 46 mm cylinder from Pinasco is now supplied with a 6-channel layout and the 5-fold bolted cylinder head manufactured for the highest loads.Various racing exhausts can be fitted to the supplied exhaust flange with 22.5 mm outer connection diameter.
The cylinder head is fitted without gasket. For optimum sealing, the tightening torque of 10 Nm for the M6 bolts and 14 Nm for the M7 stud bolts must therefore be observed.
The following parts are included in the scope of delivery:
- Additional screws for the cylinder head
- Decompressor valve (actuation not included)
- Cylinder head empty
- Cylinder and accessories
- Piston with L-ring, rectangular ring and Ø 12 mm piston pin (axe 12)
- Various gaskets for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and durable Nikasil coating are the hallmarks of this high-end tuning cylinder.
The cylinder kit develops maximum power in the mid to upper rev range. We recommend using the racing cylinder in combination with a variomatic drive.
Mounting on an original engine housing is only possible with major modifications. The cylinder kit can be mounted on the well-known Pinasco, Polini and Malossi racing cases without any adaptation work.
Note: If the cylinder kit is mounted on a Piaggio Ciao, it must be ground down on the cooling fins on the right-hand side. Due to the cut-out for the Ciao's cable duct, the hook on the head for the decompression cable is also missing. As a result, the cylinder cover is only suitable to a limited extent for Piaggio Si, Bravo of the newer generations or Grillo. This can be remedied by attaching the decompression cable to the cylinder head from the front, as on the Ciao or Boxer.
Corresponding add-on parts such as racing gearboxes, racing crankshaft, racing variator etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
Details
| Surface | varnished |
| Nominal diameter | 46 mm |
| Manufacturer | Pinasco |
| Area of application | Tuning |
| Material | Aluminum |
| Displacement | 71 ccm |
| Crankshaft stroke | 43 mm |
| Ø cylinder neck | 50 mm |
| Ø Outlet outside | 22.5 mm |
| Ø outlet inside | 18.5 mm |
| Ø piston pin (B) | 12 mm |
| Number of fixing points | 3 pcs |
| Outlet type | slanted, clamped |
| Hole spacing outlet | 48 mm |
| Thread outlet | M6x1 (standard thread) |
| Hole pattern [mm] | 55 x 34 |
| Decompressor | Yes |
| Camouflaged | No |
Suitable for the following models
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Polini Speed Engine electronic ignition housing | Piaggio Ciao, SI, Bravo, Boxer
Height: 104 mm · Width: 175 mm · Total length: 215 mm · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Stock number: 6202 · Crankshaft stroke: 43 mm · Ignition type: Electronic
EUR 240.30
Pinasco crankshaft "Racing" 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Area of application: Racing · Material: Steel · Cheek type: standard · Thread type: M8x1.25 (standard thread) · Ø coupling pin / vario pin: 12 mm · Crankshaft stroke: 43 mm · Thread length: 13.5 mm · Connecting rod length center-center: 87 mm · Number of gears: 1 pcs · Total length crankpin ignition side: 91.5 mm · Total length crankpin ignition side: 105 mm · Ø crank webs: 69.7 mm · Ø Connecting rod eye: 15 mm · Bearing seat right: 15 mm · Ø piston pin (B): 12 mm · Weight: 712 g · Ø Bearing seat (ignition side): 15 mm · Dimension needle bearing: 12 / 15 x 14.7 mm (axe 12) · Wide crank webs: 32.5 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 44 mm · Length 3rd paragraph: 63 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 14.4 mm · Ø 3rd step (on the clutch side): 12 mm · Inlet control time: 146 ° · Control time before O.T: 88 ° · Control time according to O.T: 58 °
EUR 268.90
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Material: Carbon · Manufacturer: Pinasco · Surface: varnished · Height: 38.7 mm · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Thread length: 7.5 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Weight: 650 g
EUR 240.30
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® revival parts · Diameter: 6.2 mm · Total length: 120 mm · Drive: External hexagon · Thread type: M7x1 (standard thread) · Thread length: 25 mm · Width across flats SW: 11 mm · Strength class: 8 · Strength class: 8.8
EUR 13.40
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank - 10.9 strength
Manufacturer: swiing® ingenious parts · Material: Steel · Diameter: 7.3 mm · Surface: galvanized (blue) · Thread length: 20 mm · Thread length: 30 mm · Total length: 120 mm · Thread type: M7x1 (standard thread) · Strength class: 10.9
EUR 5.60
Moped fans like you also bought:
Dell'Orto 16 mm PHBG AS carburetor hand choke
Width: 75 mm · Height: 125 mm · Manufacturer: Dell'Orto · Area of application: Tuning · Component group Carburetor: Carburetor complete · Nominal diameter: 16 mm · Carburetor type: PHBG AS · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 26 mm · Ø Internal connection: 24 mm · Ø Air filter connection: 32 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Mounting type: Plug connection clamped · Choke nozzle size: 60 · Nozzle size: 74 · Size of secondary nozzle: 50
EUR 148.70
swiing® ingenious 16 mm SHA intake manifold Speed Engine (Version 2.0) | Piaggio Ciao, SI, Bravo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Area of application: Tuning · Surface: anodized · Color: graphite colors · Total length: 29 mm · Number of fixing points: 2 pcs · Ø inside: 16 mm · Ø External connection: 19 mm · Hole spacing inlet: 36 mm · Total height: 24.2 mm · Mounting type: Screws · Camouflaged: No
EUR 37.70
Hot 
Malossi Fly Clutch converter Vario Ø 102 mm | Piaggio SI, Bravo, Boxer
Manufacturer: Malossi · Material: Steel · Number of jaws: 3 pcs · Number of springs: 3 pcs · Angle pulley: 15 ° · Gearbox type: Vario · Ø outside: 102 mm · Hardness level Counter pressure spring: Level 2 (35 kg - yellow / blue / black) · Weight: 1170 g
EUR 228.80
Polini EVO Electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Ø Internal flywheel: 80.5 mm · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Number of fixing points: 2 pcs · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 138.5 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Weight: 554 g
EUR 572.30
Collection only possible with online purchase and appointment.
